Free shipping for motorsports and aftermarket parts, sent directly from manufacturers to you.*

User
0

Jenvey Dynamics Nissan 350Z VQ 3.5L Individual Throttle Body (ITB) Kit (JEN-CKNN02)

Quick Overview

The Nissan VQ 3.5L ITB throttle body kit from Jenvey Dynamics includes six SF51/4.5/1 taper throttle bodies with an operating wheel linkage,two crossover EFI inlet manifolds, two fuel rails and six curved airhorns. This engine is used widely in front wheel drive and rear wheel drive applications like the Maxima and 350Z. This kit does not fit under the stock 350Z hood, though the JEN-CKNN02C kit does. Ships from the UK for the cost of regular US ground shipping.
OUR PRICE
$3,129.00

OR

Sold by: Jenvey Dynamics USA

We are your USA source for Jenvey ITB kits and throttle bodies. Based out of the United Kingdom, all of Jenvey's main throttle body components are made in-house including housings, spindles, butterflies, levers and fuel rails. Not only are Jenvey's products beautiful to look at, they are also highly functional, having won many races. Level X Motorsports is the exclusive distributor for Jenvey products in the United States.

Phone: 855-453-8359    Email: contact@levelxms.com
Product Description
Specifications
Vehicle Fitment

Jenvey throttle bodies and all Jenvey throttle body accessories are engineered for Motorsport, offering excellent performance, reliability, lightness and value. This kit combines a number of Jenvey pieces into one to be a complete package, ready for installation on 3.5L Nissan VQ engines such as in the 350Z or Maxima. Note that this kit does not fit under the 350Z hood, see JEN-CKNN02C for that.

This kit generally ships immediately, but may take up to 2 weeks to ship. Shipping is from UK for the cost of regular US ground shipping.

For further information, see:
  • Manufacturer Jenvey
  • Level X SKU JEN-CKNN02
  • Manufacturer SKU CKNN02
  • UPC No
  • Weight (lbs) 14.0000
  • Manufacturer Warranty 1 year
  • Country of Manufacture United Kingdom
  • Engine Type Inline-four
  • Intake Type Individual Throttle Bodies
  • Number of Manifolds 1
  • Manifold Style Straight
  • Injectors Included No
  • Fuel Rails Included Yes
  • Throttle Bodies Included Yes
  • Airhorns included Yes
No fitment data available. Please refer to the product description for details.
Throttle Bodies General Information

Why use individual throttle bodies?

There are many reasons this has been the air induction method of choice in motorsports. Read the details in our article on the benefits of individual throttle bodies.


Cross connection linkage

If necessary shorten the primary or driver lever blade to suit the throttle body mounting centres. Fit the spring clip over both primary and secondary levers and capture with the M4 balance adjusting screw and locking nut.


Balancing throttle bodies

Idle bleed screws (if fitted) should be closed at the start of this operation. Before starting the engine adjust throttle balance by setting the single idle adjuster screw so that the nearest butterfly is just visibly open, then adjust the cross-link screws so that the remaining butterflies are at a similar angle.

Start the engine and use a flow meter (SYNC10) to check airflow through each throttle body bore, adjusting as necessary. It may be necessary to re-adjust the idle during this process. Always re-check the balance on all bores after each adjustment and with the cross-link adjuster locking nuts tightened. Idle bleed screws (if fitted) may now be used to balance ports on twin bodies.

Initial set-up can be done with a feeler gauge matching the gap under the butterflies. If a flow meter is not available reasonable results can be achieved by using a length of small bore tube to listen to the flow through each bore.


Full throttle stop

The full throttle stop is usually set slightly below 90 degrees and may require adjustment. Many engines give best results at slightly less than the fully open position.


Return springs

The throttle return springs may not be sufficient to compensate for the friction and weight of the pedal and the associated linkage. All systems should be fitted with an additional return spring or CLS1 linkage kit.


Fitting the throttle position sensor

TP1 and TP2 throttle pots may be fitted either end of the throttle body, with due reference to the direction of rotation. TP8LH or RH throttle pots must be fitted to the correct end. Using the fixings supplied tighten in a central setting. After fitting, eliminate any residual side load on the spindle by holding the butterflies slightly open (e.g. a 1mm gap under the butterfly) and lightly tap the opposite end of the spindle, a plastic screwdriver handle is the ideal weight and hardness for this. Ensure that the butterflies close positively with no signs of extra friction.


Servicing

Maintenance is not normally required beyond normal adjustment and cleaning. However, if the throttle bodies are dismantled, note the following points:

- Be careful not to turn the outside edge of the seal back when refitting.
-Only replace bearings and seals with original Jenvey parts. Do not use industrial alternatives.
- New spindle covers must be pressed in and flattened using a 28mm diameter tool, supporting the body directly underneath.
- Use Loctite 243 on the butterfly screws when refitting and torque to 3NM. The projecting screw threads may be deformed for added security but spindle damage may result when the screws are next removed.
- When refitting spindle levers, ensure a gap of 0.3 to 0.5mm between the closest part of the lever and the body side when the butterfly is firmly closed.